Designed and manufactured in Saint-Eustache, Quebec, Canada since 1986

Melt-pressure measurement

Melt pressure transducers & sensors

Patt sensor families combine rigid or flexible stems with diaphragm, hazardous-area and temperature-sensing options for the actual process environment.

Engineering reference

Melt pressure transducer cross-reference & troubleshooting

Replacing a melt pressure transducer starts with the complete mechanical and electrical interface. Compare extruder pressure sensors and melt pressure transmitters by thread, signal, connector, pressure range and melt temperature.

Melt pressure transducer replacement checklist
InterfaceCommon referenceRequired replacement match
Process thread1/2-20 UNF or M18 × 1.5Thread, tip diameter, sealing seat and insertion depth must match the mounting-hole drawing.
Stem and cableRigid stem or rigid + flexible stemMatch stem length, bend clearance, cable routing and ambient temperature.
Pressure rangeFull-scale range on the original labelMatch normal pressure, excursions, overload limits and controller scaling.
Electrical output3.33 mV/V, 4–20 mA or 0–10 VMatch signal type, excitation / supply, load, wiring and input configuration.
Connector6-pin or 8-pin industrial connectorMatch connector series, keying and pin function; pin count alone is insufficient.
Melt temperature and tipFill system, diaphragm alloy and coatingSelect for actual melt temperature, chemistry and abrasive fillers. Patt offers a 440 °C option for appropriate configurations.

Use these tables to prepare a replacement request. A confirmed drop-in replacement requires Patt review of the original part number, mechanical drawing, connector pinout and operating conditions; a shared thread size or brand-family name does not establish interchangeability.

Melt pressure sensor, transducer and transmitter signal types
OutputController interfaceReplacement check
3.33 mV/VStrain-gauge bridge input with excitationAt 10 V excitation, ideal full-scale output is 33.3 mV. Confirm excitation limits, zero and shunt calibration.
4–20 mACurrent-loop inputConfirm 2-, 3- or 4-wire arrangement, supply voltage and loop load for the specific transmitter.
0–10 VAmplified voltage inputConfirm supply voltage, signal common and input impedance. A voltage input is not a current-loop input.
Documented connector examples — Dynisco manual figures 11 and 12 only
Function6-pin example: MDT 4xx, figure 118-pin example: PT 420x / 422x / 435x / TPT432x, figure 12
Positive signalAB
Negative signalBD
Positive supply / excitationCA
Negative supply / excitationDC
Calibration pairE and FE and F
Unused contactsNone shownG and H

Reference is the cable’s female connector viewed from the solder side. Six-pin: PT06A-10-6S(SR); eight-pin: PC06A-12-8S(SR). These are model-specific reference examples, not a universal or Patt pinout. Verify the complete part number and current wiring drawing before connection; do not transfer these assignments to an amplified-output model.

Five melt pressure transducer failure patterns to investigate
Observed problemLikely mechanism to checkCorrective action
Damaged or deformed tip after installationWrong port depth, damaged seat or hardened polymer in the mounting holeInspect the port against its drawing and use the specified gauge / cleaning procedure.
Torn diaphragm after a cold start or removalSolid polymer loading the thin diaphragmFollow the OEM heat-soak and removal procedure with pressure relieved and equipment isolated.
Scratched or punctured sensing surfaceMechanical cleaning tools contacting the diaphragmUse the approved cleaning method; keep abrasive tools off the sensing surface.
Permanent zero shift or unstable readings after a pressure eventOverpressure, pressure spikes, or electrical / cable damageCheck the actual pressure history, sensor rating, supply, grounding and cable before replacing the sensor.
Progressive tip erosion or pittingAbrasive fillers, aggressive polymer chemistry, or unsuitable temperature exposureReview diaphragm protection and fill-system temperature limits; discuss Patt wear- or corrosion-resistant options.
6 / 9 inRigid-stem lengths
6+6 inRigid-plus-flex format
440 °CHigh-temperature filled option
J/K/E/PT100Temperature-sensing options

Application options

Pressure measurement for difficult melts.

Diaphragm, fill, stem and certification options are selected around wear, corrosion, access, temperature and area classification.

C

Corrosion-resistant diaphragm

For aggressive melt streams and corrosive decomposition products.

Explore
W

Wear-resistant diaphragm

For filled compounds and abrasive process streams.

Explore
EX

Hazardous-area construction

Explosion-protected configurations for appropriately classified installations.

Explore

Six-inch-stem pressure transducers

Rigid-stem melt-pressure transducers for extrusion-line measurement. Select the pressure range, output and process connection to suit the installation.

Functions and options

Configure the measurement around your process

Melt-pressure sensor configurations
Function / optionAvailable configurations
Rigid stems6-inch PAT-P6 and 9-inch PAT-P9 families.
Flexible-stem arrangementPAT-P66: 6-inch rigid stem plus 6-inch flexible section for access and installation clearance.
Temperature measurementIntegrated Type J, K or E thermocouple, or Pt100 RTD; PAT-PT66 temperature-integrated family.
Corrosion-resistant diaphragmC versions for aggressive melt streams and corrosive processing conditions.
Wear-resistant diaphragmW versions for abrasive fillers and filled compounds.
Hazardous-area constructionEX configurations, including C-EX and W-EX combinations.
High-temperature optionFilled sensor variants rated up to 440 °C.
Line integrationSpecify pressure range, electrical output, process connection and required control interface with Patt.
Transducer cleaning kitsCleaning kits for transducer mounting ports help remove polymer residue and prepare the port for correct seating. Match the kit to the port geometry.

Patt Technologies

Articles & case studies

Discuss your project

Tell us what you need.

Send the polymer, throughput and operating conditions, or the drawing and material requirements for your part.

sales@patt-tech.com

+1 (450) 689-2497

Send your requirements and attach a drawing or specification. Our team will review your application.
PDF, DWG, DXF, STEP, IGES, JPG, PNG or ZIP · 15 MB maximum.